Behlen 2198162S Bedienungsanleitung PDF herunterladen

ASSEMBLY INSTRUCTIONS

THANK YOU FOR PURCHASING THIS PRODUCT

For questions about this product, or for parts inquiries, please contact our Customer Service Center listed below.

Heating Pad

Installation Instructions

F-20636-1 TECHNICAL INFORMATION 70134 Rev. 10-21-09 1-6-09

CUSTOMER SERVICE CENTER

PO Box 569

Columbus, NE

68602-0569

Ph: 1-800-447-2751

Fax: (402) 563-7447

www.behlencountry.com

PLEASE READ INSTRUCTIONS

COMPLETELY

BEFORE INSTALLATION.

Heat Pad Removal Instructions

1. Make sure the power is off.

2. Disconnect the old heat pad from thermostat

and supply line.

3. Remove old heat pad by sliding it out from

under the retainer. Some retainers can be

removed by bending the tabs in with pliers,

and some are retained with screws. Riveted

retainers cannot be removed.

4. Install the new heat pad between the retainer

and the basin.

5. Make sure the heat pad is tight up against the

basin. Bend the retainer if necessary to get a

tight fit.

6. Follow the hookup instructions for the type of

thermostat you have.

Your drinker may have one of two thermostats

the old style or the new style.

Old Style Thermostat Part Number 3668008:

Connect the flag wire connector to the black

wire on the heating pad. Connect this lead to

the thermostat, (it doesn't matter which terminal

on the thermostat you connect to). Using a wire

nut, connect the white supply wire to the white

wire on the heating pan. A short, black lead wire

with a flag terminal is used to connect the other

terminal on the thermostat to the black supply

line. Then attach the ground from the supply

line to the ground plug inside of the Handy Box

Assembly. Refer to wiring schematic on the

back for help.

Using Flag Wire Connectors:

1. Strip the wire back ½". Insert the wire into the

connector sleeve.

2. Crimp the connector with a wire crimp in the

area shown in the illustration.

3. Slide the connector onto the spade terminal

on the thermostat.

New Style Thermostat Part Number 3668011:

Strip ½" off the insulation from all wires to be

connected. Using a wire nut, connect one wire

from the thermostat to the black wire on the

heating pad, (it doesn't matter which wire from

the thermostat you connect to). Using a wire

nut, connect the white wire from the supply line

to the white wire on the heating pad. Then using

another wire nut, connect the black supply line

to the unused black wire on the thermostat.

Finally, connect the ground wire from the

supply line to the ground plug in the Handy Box

Assembly. Refer to wiring schematic on the

back for help.

Using a Wire Nut:

1. Strip wires ½" and pre-twist

stranded wire in a clockwise

direction. Twist bare wire

ends together in clockwise

direction as shown.

2. Insert wires through the

flexible sealing fingers on the supplied

silicone-filled wire nut until bottom of nut is

felt. Rotate nut clockwise until

tight. The pre-filled silicone

nut fully waterproofs the

connection. Do not reuse

connector.

Crimp

Center

only

Replacement Service Kits For

2198160S 2198161S 2198162S

2198174S 2198172S 2198175S

1 2

Inhaltsverzeichnis

Seite 1 - CUSTOMER SERVICE CENTER

ASSEMBLY INSTRUCTIONSTHANK YOU FOR PURCHASING THIS PRODUCTFor questions about this product, or for parts inquiries, please contact our Customer Servic

Seite 2 - ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONSF-19909-4 Rev. 3-17-08 8-15-02VIEW INSIDECAVITY OF DRINKERIMPORTANT NOTE:Voltage must be grounded and contain Ground FaultCircuit

Verwandte Modelle: 2198172S | 2198160S |

Kommentare zu diesen Handbüchern

Keine Kommentare

Behlen 2198162S Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Haustiere Behlen 2198162S herunter. Behlen 2198162S User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 2198172S | 2198160S |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Haustiere Behlen 2198162S